This is merely a historical archive of years 2008-2021, before the migration to mailman3.
A maintained and still updated list archive can be found at https://lists.osmocom.org/hyperkitty/list/gerrit-log@lists.osmocom.org/.
Max gerrit-no-reply at lists.osmocom.orgReview at https://gerrit.osmocom.org/4153 logging: replace OpenBSC -> OsmoBSC in examples Change-Id: Id55dcd41b0d2b3408969d1858e925da55fb5427c --- M common/chapters/logging.adoc 1 file changed, 14 insertions(+), 14 deletions(-) git pull ssh://gerrit.osmocom.org:29418/osmo-gsm-manuals refs/changes/53/4153/1 diff --git a/common/chapters/logging.adoc b/common/chapters/logging.adoc index 564f6d2..28b6d3e 100644 --- a/common/chapters/logging.adoc +++ b/common/chapters/logging.adoc @@ -47,7 +47,7 @@ Next, you can configure the log levels for your VTY session. Each sub-system of the program in question typically logs its messages as a different category, allowing fine-grained control over which log -messages you will or will not see. For example, in OpenBSC, there are +messages you will or will not see. For example, in OsmoBSC, there are categories for the protocol layers `rsl`, `rr`, `mm`, `cc` and many others. To get a a list of categories interactively on the vty, type: `logging level ?` @@ -80,7 +80,7 @@ really means that all events with a level of at least __info__ will be logged, i.e. including events of __notice__, __error__ and __fatal__. -So for example, in OpenBSC, to set the log level of the Mobility +So for example, in OsmoBSC, to set the log level of the Mobility Management category to info, you can use the following command: `log level mm info`. @@ -117,10 +117,10 @@ To configure a new log file, enter the following sequence of commands: ---- -OpenBSC> enable -OpenBSC# configure terminal -OpenBSC(config)# log file /path/to/my/file -OpenBSC(config-log)# +OsmoBSC> enable +OsmoBSC# configure terminal +OsmoBSC(config)# log file /path/to/my/file +OsmoBSC(config-log)# ---- This leaves you at the config-log prompt, from where you can set the @@ -151,10 +151,10 @@ following commands on the VTY: ---- -OpenBSC> enable -OpenBSC# configure terminal -OpenBSC(config)# log syslog daemon -OpenBSC(config-log)# +OsmoBSC> enable +OsmoBSC# configure terminal +OsmoBSC(config)# log syslog daemon +OsmoBSC(config-log)# ---- This leaves you at the config-log prompt, from where you can set the @@ -177,8 +177,8 @@ In order to configure logging to stderr, you can use the following commands: ---- -OpenBSC> enable -OpenBSC# configure terminal -OpenBSC(config)# log stderr -OpenBSC(config-log)# +OsmoBSC> enable +OsmoBSC# configure terminal +OsmoBSC(config)# log stderr +OsmoBSC(config-log)# ---- -- To view, visit https://gerrit.osmocom.org/4153 To unsubscribe, visit https://gerrit.osmocom.org/settings Gerrit-MessageType: newchange Gerrit-Change-Id: Id55dcd41b0d2b3408969d1858e925da55fb5427c Gerrit-PatchSet: 1 Gerrit-Project: osmo-gsm-manuals Gerrit-Branch: master Gerrit-Owner: Max <msuraev at sysmocom.de>